30 m (100 ft.) Steel Long Tape
Product Description:
JK Cement Tile MaxX Tile Grout is a premium dry pre-mix and water resistant cement based tile jointing grouts. It is a non-sanded product and is recommended for internal and external use. It is available in White and different range of standard colors. It can be applied up to 5 mm jointing for walls, balconies, floor, wet areas and stairs tilling.
Properties :
- Non shrinkage
- Excellent water resistance
- Flexible to apply
- Suitable for wet areas
- Easy to clean
- Available in a wide range of attractive colors
Technical Features:
Properties | Results |
---|---|
Appearance | White Powder |
Composition | White Cement, Fine Graded Fillers, Re-dispersible Polymer powder and performance enhancing Additives |
Aggregate Size | >0.150 mm |
Compressive Strength* as per EN:1015-11 (28 days) | >6 N/mm² |
Flexural Strength* as per EN:1015-11 (28 days) | > 2.5 N/mm² |
Bond Strength* as per EN:1015-12 (28 days) | ≥ 1 N/mm² |
Water Retention* as per ASTM C1506 – 17 | ≥ 95 % |
Setting Time* at 25ºC | 7 -9 Hours |
Bulk Density | (Kg/Liter) 1 ± 0.10 |
Mixing Ratio | 6.6 – 7.6 Liters/20 Kg Bag & 8.3 – 9.5 Liters/25 Kg Bag |
Pack Size | 20 & 25 Kg Bags |
Application Thickness | Total Thickness of Maximum 3 mm in multiple layers |
Consumption | Approximately 1.25 – 1.75 m²/Kg * |
* Based on laboratory values tested at Standard Conditions of Temperature and %Relative Humidity
Scope of use:
JK Cement Tile MaxX Tile Grout are suitable for filling up to 5 mm joints between ceramic tiles, marbles tiles, glass mosaic tiles, natural stones and porcelain tiles.
Surface Preparation:
The grooves between the tile surfaces to be grouted must be completely cleaned prior to the application of the JK Cement Tile MaxX Tile Grout.
Mixing
JK Cement Tile MaxX Tile Grout is to be mixed with 30 – 35% of fresh and potable water in a clean and non-corrosive container. It is strongly recommended to use a proper electrical mixer for achieving homogenous mixture. Once mixed, wait for 5 minutes and mix again prior to application. Mix only the needed quantities to avoid any material loss due to drying in the container by time. Also, avoid adding any excess water after mixing. Care should be taken that the mixture is completely free from any lumps, prior to application.
Application
Apply JK Cement Tile MaxX Tile Grout within readily cleaned and free of dust joints using rubber spatula. Compact the grout within joints properly.
Remove excessive grouts using dampen sponge. It is strongly recommended to consume the mixed grouts within 90 minutes. Once grouts are dried, use dry cloth to remove unwanted grouts from tiles surface and clean it.
Curing
After application, it should be cured using dampen sponge or cloth for a minimum of 2 – 3 times a day for 48 hours
Recommendations:
- Ensure to not use it on metal, gypsum and other non-absorbing surfaces
- Refrain from application during rain, unstable weather conditions or under direct sun
- Do not mix different grout colours together which will increase the risk of colour inconsistency in final
- Do not add any salty or dirty water for
- The amount of mixing water must be precisely Excess water could induce efflorescence over the surface. Different color tones will result if mixture is prepared with different water ratios.
Storage:
- Shelf Life: 12 Months from date of manufacture if covered well and stored in pallets, away from heat, Sun light and
Health & Safety:
JK Cement TileMaxX Tile Grouts contains cement which becomes strongly alkaline upon mixing with water and this may cause skin irritation when exposed for very long time. Avoid contact with eyes and inhalation of dust. In case of skin/eyes contact, wash with plenty of clean water and seek medical attention immediately. It is highly recommended to use all relevant Personal
Protective Equipment while handling it and work in well ventilated conditions while applying it. Keep out from the reach of children.